DATASHEET
5.0mm Infrared LED
IR383
Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest
possible temperature is desirable for the LEDs.
?
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.
4.
Cleaning
?
?
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED
5.
Heat Management
?
?
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.
6.
ESD (Electrostatic Discharge)
?
?
?
?
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of
friction between LEDs during storage and handing.
7.
Other
?
?
?
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above
specification.
When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t
reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.
8
: (3)
Revision Copyright ?
No: Release Date:
2010, Everlight All Rights Reserved. Release Date : JUL.10.2013. Issue DIR-0000988
www.everlight.com
LifecyclePhase:
Expired Period: Forever
相关PDF资料
IR42-21C/TR8 LED IR SUBMINI 1.8MM ROUND SMD
IR533C LED IR SMD GAA1AS WATER CLEAR
IR67-21C/TR8 LED IR TOP GAA1AS WATER CLR SMD
IR7373C LED IR 5MM GAA1AS WATER CLEAR
IR7393C LED IR 5MM GAA1AS WATER CLEAR
IR908-7C-F LED IR 1.5MM SIDE FACE WATER CLR
IR91-21C/TR10 LED IR 1.9MM ROUND SUBMINI ZBEND
IR91-21C/TR7 LED IR 1.9MM RND SUBMINI GULLWIN
相关代理商/技术参数
IR3831MPBF 制造商:IRF 制造商全称:International Rectifier 功能描述:HIGHLY EFFICIENT INTEGRATED SYNCHRONOUS BUCK REGULATOR FOR DDR APPLICATIONS
IR3831MTR1PBF 功能描述:直流/直流开关调节器 8A SupIRBuck Reg 250-1500kHz, 1.5-16V RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
IR3831MTRPBF 功能描述:直流/直流开关调节器 8A SupIRBuck Reg 250-1500kHz, 1.5-16V RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
IR3831WMPBF 制造商:IRF 制造商全称:International Rectifier 功能描述:HIGHLY EFFICIENT INTEGRATED SYNCHRONOUS BUCK REGULATOR FOR DDR APPLICATIONS
IR3831WMPBF_1 制造商:IRF 制造商全称:International Rectifier 功能描述:HIGHLY EFFICIENT INTEGRATED SYNCHRONOUS BUCK REGULATOR FOR DDR APPLICATIONS
IR3831WMPBF_11 制造商:IRF 制造商全称:International Rectifier 功能描述:HIGHLY EFFICIENT INTEGRATED SYNCHRONOUS BUCK REGULATOR FOR DDR APPLICATIONS
IR3831WMTR1PBF 功能描述:直流/直流开关调节器 8A SupIRBuck Reg 250-1500kHz, 1.5-16V RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
IR3831WMTRPBF 功能描述:直流/直流开关调节器 8A SupIRBuck Reg 250-1500kHz, 1.5-16V RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5